12v6ah rechargeable lithium battery pack

12v6ah rechargeable lithium battery pack


1.Safety: safest Li-Ion battery, none fire or explosive

2.Clean and Green energy, no toxic material contained

3.Long life cycle, 80% capacity remain after 500 times deep cycle.                            4.No memory effect,highly efficient charge anytime, no reduction of capacity

5.Operation temperature: -20~60°C

6.Small size, light weight:

7.Good performance at high temperature and high temperature resistance

8. Low self-discharge rate: < 3% monthly

  • Description
  • Inquiry


1.Safety: safest Li-Ion battery, none fire or explosive

2.Clean and Green energy, no toxic material contained

3.Long life cycle, 80% capacity remain after 500 times deep cycle.

4.No memory effect,highly efficient charge anytime, no reduction of capacity

5.Operation temperature: -20~60°C

6.Small size, light weight:

7.Good performance at high temperature and high temperature resistance

8. Low self-discharge rate: < 3% monthly


Emergency Power System
Power tools,elecrtic scale
Alarm system
Telecommunication systems
LED products
Uninterruptible power supplies
Fire and Security System
Electric toys
Solar and wind power system
Stereo systems, etc




This specification describes the relevant reference requirements of 18650/3S5P/6AH/12V lithium ion secondary batteries provided by Shenzhen Xbatt Energy Technology Co. Ltd.

二、电池类型与型号(Battery TYPE&MODEL)

1、电池类型(Battery type):锂离子二次电池(Secondary lithium ion batteries)

2、电池型号(Battery model):18650/3S5P/6AH/12V

三、引用标准(Reference Standard


This standard refers to GB/T18287-2013, GB31241-2014, UL1642 and other technical standards.

四、额定规格(Rated Specifications

项 目 Item 规格 Specifications

Minimum Capacity (0.2C5A discharge)




Nominal Capacity (0.2C5A discharge)

3.额定电压 Nominal Voltage 12V
4.放电终止电压(最小) Discharge Cut-off Voltage 8.25±1.5V
5.充电限制电压(最大) Max Charge Voltage 12.6V
6.充电电流(标准) Standard Charging Current 1.5A
7.放电电流(标准) Standard Discharge Current 1.5A
8.充电电流(最大) Max. Charge Current 3.6A

Continuous Maximum Discharge Current

11.内阻 Impedance ≤96mΩ
12.重量 Weight 0.5kg
13.外形尺寸Outline Dimension 57*57*73mm
14.外露线Exposed line 100-305mm
14.正极Positive Red wire with 3135 16AWG
16.负极Positive Black wire with 3135 16AWG
15. 工 作 温 度 Operating Temperature 充电Charging 0~45℃
放电Discharging -20~60℃
16.储存温度 Storage Temperature -20~60℃
17.标准环境Standard Environmental Condition 温度Temperature 25±2℃
湿度Humidity 45-75%RH
湿度Humidity 45-75%RH
大气压Atmospheric Pressure 86-106KPA

五、电性能(Electrical Characteristic)

项目 Item 测试方法 Test Method 标准Standard






1.充电制式Charging System






Charge with 0.5C5A current under the condition of the ambient temperature at 25±5℃. When the battery voltage reaches 12.6V,change to charge with constant voltage till the

current less than or equal to 0.02C5A. The charging

process takes 3.5 hours.











A fter the Battery being standard charged, set it aside for 5 minutes, and then discharge continuously with 1C5A current to8.25V termination voltage. Repeat the above steps for three times and record the third length of time for capacity discharge. The the discharge time is required ≥51minutes








3.循环寿命Cycle Life





At 25±5 ℃, charge to 12.6V with 0.5C5A constant current, until charging current is ≤240mA. Shelve for 5 minutes, then discharge to 3.0V with0.5C5A constant current, and shelve for 5 minutes. Repeat the above steps until the discharge capacity is 80% of the initial capacity. The cycle life is required ≥500 times







4.荷电保持能力Normal Storage


在20±5℃状态下,标准充饱电后,电芯搁置28天,然后用0.2C5A放电至2.75V,所记录放电时间. ≥240分钟



At 20±5℃, rest the battery for 28 days after it being standard charged. Then discharge its voltage to 2.75V with 0.2C5A current. Record the discharging time. ≥240minutes.

六、环境适应性(Environment Adaptation Performance)

项目 Item 测试方法 Test Method






1. 振动



充电后电池在相互垂直的X、Y、Z三个方向上从10Hz~55Hz 循环扫频振动30min,扫频频率10-55Hz,扫频速率为1oct/min




Equip it to the vibration platform, adjust and prepare the test equipment according to following vibration frequency and relevant swing, doing frequency sweeping from X, Y, Z three directions, each from 10Hz to 55Hz for 30 minutes of recycling, rating of which is 1oct/min: No remarkable damage、No smoking 、

No explosion




2.高温放电Discharge at high temperature


2.75V,所记录放电时间. ≥57分钟



A fter the Battery being standard charged,rest the cells for 2h at 55±2℃. Then dischargE at 1C5A to voltage 2.75V. Record the discharging time. ≥57 minutes





3.低温放电Discharge at low temperature



2.75V,所记录放电时间. ≥180分钟



After the Battery being standard charged, rest the cells for 16h at

-10±2℃, then discharge with 0.2C5A current to voltage 2.75V. Record the discharging time. ≥180minutes







4. 自由跌落









The battery from the 1 meter high free fall to the 20mm thick hard board, from X, Y, Z positive and negative direction (in the direction of each aspect of the free fall 1 times). No leakage, No smoke, No explosion.

七、安全性能(Safety Characteristic)

项目 Item 测试方法 Test Method




1、常温短路性能Short Circuit at Room Temperature

电池标准充电后,将接有热电偶的电芯置于环境温度20±5℃的防爆箱中,短路其正负极,短路导线电阻80±20mΩ,试验过程中监视电芯温度变化,当电芯温度下降到比峰值低约10℃时, 或短接时间达到24h后结束试验。 不爆炸、不起火最高温度。

After the Battery being standard charged,keep the battery connected with a thermocouple in a explosive -proof box at 20 + / – 5 ℃.

Short circuit the positive and negative terminals, and the conductor resistance to 80 + 20 m Ω. Monitor change of the cell’s temperature during the process of test. Stop the test when the temperature falls to the value that about 10℃ lower than the peak value ,or if the short

circuited time is up to 24 hours. <150℃ No fire No explosion





2. 过放

Over Discharge

电池以0.2C5A放电至2.75V,然后在正负极之间接上30Ω电阻, 放置24h,观察电芯外观。不起火、不爆炸

After being standard charged, discharge the battery to 2.75V with 0.2C5A, and then use a 30 resistor to connect the battery positive and negative terminals for 24 hours. Observe the appearance of the

electric core. No fire, No explosion





3. 过充


电池标准充电后,将电池置于防爆箱内,连接电芯正负极于恒流恒压电源,调节电流至3C5A,电压上限为4.8V,然后对电芯进行充电,直到电芯电压达到最大输出电压后,再持续充电7h 或电池温度下降到比峰值低20%,测验结束。不起火,不冒烟

The Battery being standard charged, put the battery in an explosion- proof box and connect the positive and negative electrode of the battery with a power supply that provides steady current and voltage.Then adjust current to 3C5A, and set the voltage’s upper limit to 4.8V. Keep charging until the maximum output voltage is reached. The test can be finished after continuing to charge for 7 hours or when the temperature of the battery drops to 20% below

the peak value. No smoke or fire




4. 重物冲击

Impact Test



The Battery being standard charged,put the battery on the impact table and place a steel column (Φ15.8 + 0.2 mm) is placed on the center of the battery. Let a hammer (9.1 + 0.1 kg) fall off to the steel column above the battery center from the height of 61cm. After

that,observe the battery for 6 hours. No fire, No explosion





5. 挤压



The Battery being standard charged, put the cell between two planes and press it perpendicular to the direction of the plate. continue crushing until the force reaches 13.0kn + 0.78kn. Once the pressure reaches the maximum, the extrusion test can be. No fire, No explosion


6. 热冲击

Hot Oven



30min 不起火、不爆炸。

The Battery being standard charged,put the battery in high temperature explosion-proof box, with 5 + 2 ℃ / min temperature rising rate of temperature. When the temperature reaches 130 + 2 ℃ in the cabinet, keep that temperature for another 30 min.  No fire, No explosion.



To ensure proper use of the battery please read the manual carefully before using it. Handling


Do not expose the battery to the sun or discard the battery in fire.


Do not reverse the positive and negative terminals when charging.


Avoid shorting the battery.


Avoid excessive physical shock or vibration.


Do not disassemble or deform the battery.


Do not immerse the battery in water.


Do not use the battery mixed with other batteries of different mannfacturers,types and models.


Keep the battery out of the reach of children.

充放电charging and discharging


The battery must be charged under appropriate conditions only.


Never use a modified or damaged charger.


Do not leave the battery in charger for over 24 hours.

贮存 storage


Store the batttery in a ventilated and dry environment.Long-term storage is not recommanded. When the storage time exceeds 3 months, it is recommended to do a complete charge-discharge cycle every 3 months.



Regulations vary from different countries. Dispose of the battery in accordance with local regulations.

Online Service
Live Chat