Xbatt BatteryTelecom Battery48 V StringAGMCapacity TestSite Maintenance

One Weak Block Is Enough to Fail a 48 V String

A coastal macro site held forty minutes instead of four hours. Block three read 10.2 V open circuit and tested at 31% capacity; the other three were above 90%. One block decides the string, and the rectifier never sees it coming.

One Weak Block Is Enough to Fail a 48 V String

A macro site on the coast, four 12 V 100 Ah AGM blocks on a string, commissioned in the dry season. Eighteen months later the site dropped to battery and stayed up for forty minutes instead of the four hours on the design sheet.

The maintenance report had one line that matters: block three read 10.2 V on open circuit, the other three read 12.6, 12.6 and 12.6. Capacity test on block three came back at 31% of rating. The other three were above 90%.

Nothing was wrong with the string except one block, and one block was enough. This is not bad luck. It is what series strings do.

Why the weak block always loses

Four blocks in series share one current. They do not share one voltage.

On charge, the block with the least capacity reaches full first. The charger keeps pushing the same current through all four, so that block sits at absorption voltage longer than it should and gasses. On discharge, the same block hits empty first, and the other three keep pulling — through it, in reverse. A cell driven below zero volts does not recover. It sulphates hard, its internal resistance climbs, and it becomes the block that drags the string down next cycle.

You can see the whole failure in one number: the spread between block voltages at the end of discharge. New string, maybe 0.15 V. Doomed string, 1.5 V or more.

There is no balancer in a lead-acid string. There is no BMS watching individual blocks. The string trusts that four jars from the same production batch, at the same temperature, with the same torque on the terminals, will age at the same rate. In a temperature-controlled room they mostly do. In an outdoor cabinet in July, they do not.

The cabinet is doing most of the damage

An outdoor cabinet in direct sun is not 35 °C inside. We have logged 52 °C at the top of a cabinet with the door closed at two in the afternoon, and 38 °C at the bottom. That gradient alone is enough to make the top blocks age faster than the bottom ones, which is exactly the pattern in the report above — block three was the top one.

Two things break at that temperature, and the second one is the one people miss.

The first is life. Lead-acid loses roughly half its calendar life for every 8–10 °C above 25 °C. At 50 °C you are not getting four years, you are getting about eighteen months, which is what happened.

The second is float voltage. A vented or valve-regulated block wants about 13.5–13.8 V at 25 °C, compensated downward by roughly 18 mV per °C above 25 for a 12 V block. Most outdoor rectifiers either do not compensate at all or compensate against the rectifier's own internal sensor, which sits in the equipment bay, not next to the battery. At 50 °C the correct float is around 13.1 V. If the rectifier is still holding 13.6 V, you are overcharging by half a volt, continuously, for months. That is grid corrosion and water loss on a schedule.

If there is one cheap fix in this whole article, it is a temperature sensor on the battery, wired to the rectifier's compensation input. If the rectifier cannot take one, the cabinet needs shading and forced ventilation before anything else is specified.

Connections, torque, and the boring failures

The other half of field failures are mechanical, and they look electrical.

A loose terminal adds resistance. Resistance adds heat. Heat accelerates corrosion, which adds more resistance. One block in the string ends up slightly undercharged because the voltage drop across its connection eats part of the charge voltage. It sulfates quietly for a year, then becomes the weak block.

Three things worth putting in the maintenance schedule, none of them expensive:

  • Torque check on every inter-block link at commissioning and annually, to the datasheet value with a calibrated wrench
  • Voltage spread across all blocks at end of discharge — this is the single most useful measurement in a telecom battery room, and it takes four minutes
  • Internal resistance or conductance on each block, trended. One reading means nothing. Six readings a year apart show you the block that is going before it takes the site down

The [internal resistance test](/news/lead-acid-battery-internal-resistance-testing) article covers how to read those numbers without over-interpreting them.

What actually fixes it

You can keep four 12 V blocks and manage them harder, or you can change the architecture.

4 × 12 V AGM blocks 24 × 2 V OPzV cells 51.2 V LiFePO4 pack
Points of failure per 48 V string 4 jars, 3 links 24 cells, 23 links 1 pack, internal BMS
Balancing None None, but cells are individually testable Active, per cell group
Thermal uniformity in cabinet Poor — top blocks run hotter Better — cells sit in one plane Good, one case
Float voltage tolerance Wide, easy to overcharge Wider, more electrolyte Managed by BMS
Cycle life at 50 °C ~18 months ~3 years ~5 years
Field serviceability Swap one block Swap one cell Swap module
Relative cost per kWh Lowest Mid Highest

The honest read: 2 V cells win on serviceability and thermal behaviour because you can measure and replace one cell, and because 24 cells in a rack share a temperature plane better than four blocks stacked in a column. LiFePO4 wins on life at high temperature and loses on cost per kWh and on cold-weather charging, which matters if the site is anywhere the temperature goes below zero.

What we would not do is put four 12 V blocks in a sealed outdoor cabinet in a hot climate and expect four years. That specification gets written because it is the cheapest line on the bill of materials, and it fails for a reason that has nothing to do with the brand of battery.

For the RFQ

  1. Load profile in amps, average and peak, and required backup hours at end of life
  2. Cabinet internal temperature, summer maximum, measured at the top of the battery stack rather than at the door
  3. Whether the rectifier has battery temperature compensation, and where its sensor sits
  4. Float and boost voltages actually set on site, not the defaults in the manual
  5. Whether the site can accept a 2 V rack instead of a 12 V block column — this is a mechanical question before it is an electrical one
  6. Who tests the string, how often, and what they record

If you are replacing strings on a schedule rather than on failure, the schedule is the design. Send us the load profile and the cabinet temperature and we will tell you which of the three architectures survives it — [TBS series](/products/tbs-series-telecom-base-station) for a 51.2 V drop-in, [OPzV](/products/opzv-series-tubular-gel) where the rack allows 2 V cells, and [FT series](/products/ft-series-front-terminal) for 19-inch and 23-inch racks where front access is the constraint.

The block that failed was not defective. It was the one that ran hottest, got overcharged longest, and had nobody measuring it. Fix the cabinet and the measurement, and the same battery lasts twice as long.

Looking for a reliable battery supplier?

Send us your requirements — model, quantity and target market. Quote within 24 hours.

Get a Quote