Xbatt BatteryFloat VoltageVRLATemperature CompensationUPSTelecom

2.27 V Is Not a Setting. It Is a Temperature.

The gap between a cell that sulfates and a cell that dries out is about 50 millivolts, and the room is never at 25 °C. Where the sensor goes decides whether the bank reaches year eight.

2.27 V Is Not a Setting. It Is a Temperature.

2.27 V is not a setting. It is a temperature.

Open almost any VRLA datasheet and you will find the same line: float charge 2.27 V per cell at 25 °C. Sometimes a range, 2.25 to 2.30. Almost always with that little "at 25 °C" attached, in the same way a car spec says fuel consumption "at 90 km/h" — technically true, and quietly useless the moment conditions change.

Here is the part that costs people money. The gap between a cell that sulfates and a cell that dries out is about 50 millivolts. That is not much room. And a battery room does not sit at 25 °C, except in the commissioning report.

I have stood in telecom cabinets in Jakarta where the internal temperature at three in the afternoon was 41 °C while the air conditioning controller, mounted on the wall outside, read 24. Same cabinet. A charger with a fixed 2.27 V/cell setting is, in that room, overcharging every cell by about 50 mV, every hour, for years.

What overcharging actually does

Overcharge in a VRLA cell means the oxygen recombination cycle cannot keep up. Water is electrolysed, the cell cannot be topped up, and the electrolyte slowly dries. As it dries, the internal resistance climbs and the cell runs hotter — which accelerates the drying. It is a loop, and it ends with one block in the string reading 10.4 V while the rest are fine.

The rule of thumb everybody quotes is that every 10 °C above 25 °C halves the life. It is an Arrhenius approximation, not a law, but the direction is right and the magnitude is close enough that it belongs in your planning.

At the other end, cold does the opposite. A cell held at 2.27 V in a 5 °C cabinet is undercharged. Undercharge leaves lead sulfate on the plates that never quite converts back, and that is the sulfation you read about in every solar article, arriving by a different route — not from cycling, but from a charger that was set correctly for a room the battery is not in.

The compensation, in one line

Most VRLA makers publish a coefficient of about -3 mV per °C per cell, referenced to 25 °C. Some say -3.5, some -4. Use the number on your own datasheet; if there is none, -3 mV is the usual starting point.

U(float) = (2.27 - 0.003 × (T - 25)) × number of cells

Twenty-four cells, a 48 V string, cabinet at 35 °C:

(2.27 - 0.003 × 10) × 24 = 2.24 × 24 = 53.8 V

The commissioning sheet says 54.5 V. So the correct setting in that cabinet is 0.7 V lower than the number written on the sheet, and nobody ever goes back to change it.

At 5 °C the same string wants 2.285 × 24 = 54.8 V. Slightly higher, not lower. If your charger only compensates downwards on hot days and clips at 54.5 V, you are undercharging all winter.

Where the sensor goes

This is where most installations get it wrong without noticing. The temperature that matters is the cell temperature, not the room's.

  • Put the sensor on a pilot cell, in the middle of the bank, ideally on the negative terminal of a block that sits in the middle row. That is where the bank runs hottest.
  • On a multi-tier rack, the top tier is warmer than the bottom by several degrees. One sensor on the bottom tier will under-read and the top tier will dry out first.
  • Wall-mounted controllers measure the wall. A wall next to a door, or above a rack, is not the battery.
  • If the string sits in an outdoor cabinet, the sensor needs to survive the same temperature the cells do, and the charger needs a compensation range that reaches down to -20 °C, not one that stops at 0 °C.

Then there is the thing nobody does: re-check the setting after the HVAC is serviced, after a rack is reloaded, after the room gets a second string. The compensation curve is only as good as the temperature it is fed.

What good looks like in practice

Once a quarter, at the same time of day, write down:

  • the cell temperature at the pilot cell, and the room temperature next to it — if they differ by more than 3–4 °C, the sensor is in the wrong place;
  • the float voltage at the charger terminals, and at the far end of the string;
  • every cell's voltage. On 2 V cells a spread wider than about 50 mV is worth a second look, and one cell sitting 100 mV below the average is a cell on its way out.

That is fifteen minutes of work. The alternative is discovering it through a failed discharge test two years later, which is the plot of this article on internal resistance.

The two mistakes I see most

Treating 2.27 as a constant. It is a value at a reference temperature. If the datasheet says "at 25 °C" and the charger has no temperature input, the installation is running open-loop, and the only question is whether it fails by drying or by sulfating.

Compensating for the wrong place. A sensor on the wall, a sensor on the bottom tier, a sensor that got moved during a maintenance visit. All three produce a charger that believes it is doing the right thing. The cells know better.

For a standby string the float setting is the single parameter you can still change after the container has shipped, and it is the one that decides whether the bank reaches year eight or year four. On a telecom site or a UPS room, where the battery may discharge for fifteen minutes a year, float voltage is effectively the whole of its life. It is worth the fifteen minutes.

Looking for a reliable battery supplier?

Send us your requirements — model, quantity and target market. Quote within 24 hours.

Get a Quote