That 1,200-Cycle Claim Has a Test Method Behind It. Ask What It Is.
One cell, three quotations, three cycle numbers: 1200, 1500 and 3000. Every figure honest, none of them comparable. Depth, temperature, discharge rate, charge factor and the end-of-life threshold decide the answer — and only one of those five is usually printed.

Three quotations, three cycle numbers, one battery
I was going through a tender pack last month — a 400 kWh off-grid job, nothing exotic — and the same cell was quoted three times. 1200 cycles. 1500 cycles. 3000 cycles. Same nominal capacity, same 2 V tubular construction, prices within fifteen percent of each other.
All three numbers were honest. That is the part that unsettles people. None of the three suppliers was lying, and you still cannot put those numbers next to each other and pick a winner, because each one was measured under conditions the other two did not use.
A cycle count without its test conditions is not a specification. It is a mood.
Four dials, and every supplier sets them differently
Strip a cycle-life claim down and there are only four things that decide the answer, plus a fifth that decides when you stop counting.
Depth of discharge. A cell cycled to 30 % will outlast the same cell cycled to 80 % by a factor of three or four, in rough terms. This one everybody knows, and it is usually stated.
Temperature. Almost every lead-acid cycle figure is quoted at 25 °C. Run the same cell at 40 °C and you lose a large part of it. The old rule of thumb — chemical reaction rate roughly doubles per 10 °C — is why the industry says life halves for every 10 °C above 25 °C. It is an approximation, not a law, but it is close enough that a cabinet running at 38 °C will not deliver the catalogue number, and nobody puts that on the first page.
Discharge rate. Cycling at C10 and cycling at C3 are different tests. Higher rate, more voltage sag, earlier end-of-discharge, and the plate sees more mechanical stress per cycle.
Charge factor — and this is the one that gets quietly forgotten. How much energy goes back in, relative to what came out? 105 %? 110 %? 115 %? Charge too little and sulfate accumulates; charge too much and you grid-corrode the positive plate and dry out the electrolyte. Some test profiles return 100 %, which is physically unrealistic and flattering to the result.
End-of-life criterion. Do you stop at 80 % of rated capacity, or 60 %? IEC 61427 stops at 80 %. A supplier using 60 % can legitimately print a much bigger number for the same cell.
Two cells, identical construction, can differ by 2.5× on paper purely from these five settings. No dishonesty required.
What IEC 61427 actually is, and why it matters here
If you specify storage batteries for renewable energy — stationary tubular or AGM — the standard that should be behind the number is IEC 61427. Part 1 covers photovoltaic off-grid applications; Part 2 covers on-grid.
The important thing about it is not the paperwork. It is that the test profile is built to imitate what a solar site actually does to a battery, rather than what a laboratory finds convenient.
A conventional cycle test is a clean loop: charge to full, discharge to a set depth, rest, repeat. Every cycle identical, every cycle ending at 100 % state of charge. It is a good test of the plate, and a poor description of a solar installation, where the battery may go three weeks without ever reaching full because it rained.
IEC 61427's cycling regime mixes shallow daily cycles with periodic deeper discharges, and checks capacity at intervals rather than after every event. That structure exists precisely because the failure mode on a real site is not "too many cycles" — it is "too many cycles that never finished charging."
So when a supplier writes 1500 cycles, the first useful question is not "is that good?" It is "which profile produced that number?" A figure from a clean 100 %-recharge loop and a figure from a solar-shaped profile are not the same measurement, even when they are printed in the same font.
The part where a good number hides a bad battery
Here is a concrete way this goes wrong, and I have seen the pattern more than once.
A cell with a thick, heavily pasted positive plate will post an excellent cycle count under a shallow, gentle profile, because the paste has plenty of material to lose before capacity drops below 80 %. Put the same cell on a solar site with a chronic undercharge, and the sulfate that forms on that thick plate is harder to convert back — more material, deeper discharge into the plate's interior, longer diffusion path. The number that looked like a strength becomes the reason it dies early.
Conversely, a thinner plate with a properly matched charge profile can beat it in the field while losing on the datasheet.
This is why I keep saying the datasheet is a filter, not an answer. Use it to eliminate the obviously unsuitable. Do not use it to rank two cells that both passed.
What the numbers on a real site actually look like
Rough shapes, from experience and from what the standards describe — treat these as orders of magnitude, not guarantees:
- A standby installation: 3–20 discharges a year, mostly partial, always recharged. Cycle life is irrelevant; grid corrosion sets the calendar life. You should be buying on float life and temperature tolerance, and arguing about cycles is wasted breath.
- Grid-tied self-consumption: one cycle a day, 40–70 % depth. This is the mainstream case now, and it is the one where the difference between plate designs shows up inside three years.
- Off-grid solar: 300+ cycles a year at moderate depth, plus a long undercharge season. This is the harshest duty in the catalogue, and the one where a test profile that assumes full recharge is most misleading.
- Peak shaving, two cycles a day: 500–700 a year. At this point you are choosing between plate constructions, not between brands.
Notice that only two of those four are really "cycle life" problems. The other two are float-life and charge-acceptance problems wearing a cycle count as a disguise.
Five questions that settle it
When a cycle number arrives in a quotation, I would send these back. They are short, they are answerable in one line each, and a supplier who cannot answer them has told you something useful.
- Which standard, and which part? IEC 61427-1, IEC 61427-2, IEC 60896-21, or "internal method". All are legitimate answers. "Internal method" with no profile description is not.
- At what depth of discharge, and at what temperature? Both, in the same sentence, or the number is incomplete.
- What charge factor does the test use? If the answer is 100 %, the test never reproduced a real site. If it is 110 %, now we are talking.
- What is the end-of-life threshold? 80 % of rated capacity, or 60 %? A 60 % threshold inflates every number on the sheet.
- Can I see the capacity-versus-cycle curve, not just the endpoint? The shape matters more than the final figure. A curve that holds flat then falls off a cliff tells you the plate is behaving; a curve that slides steadily from cycle 100 tells you the design is marginal for the duty.
Five questions. If two suppliers answer all five and one answers none, you have your shortlist, and you did not have to trust anybody's marketing department.
The temperature thing deserves its own paragraph
Because it quietly destroys more storage banks than any warranty dispute I have been part of.
The 25 °C reference is not a detail, it is the whole basis of the claim. A battery room at 35 °C is not "a bit warm". Under the halving rule, it is running at something close to half the quoted life. At 40 °C, worse.
And where does the heat come from? Often not the ambient. It comes from the battery itself, during charge — particularly in a sealed cabinet with no airflow and cells packed tight. A telecom hut in a hot climate with a closed door and a string of 24 cells is a very different thermal environment from the test bench.
So when you compare a 20-year design life against a 12-year one, ask what temperature each assumes, and then ask what the actual site will be. If the site runs hot, both numbers shrink, and the gap between them may shrink with them — or invert, if one design has better charge acceptance and therefore generates less heat while charging.
That last sentence is the kind of thing you only learn by opening cabinets.
What belongs in the purchase order
Not the cycle number. The conditions.
Something like: cycle endurance tested to IEC 61427-1 at 25 °C ambient, 60 % depth of discharge, C10 discharge, charge factor ≥ 1.10, end of life at 80 % of rated capacity; test report to be supplied with the shipment.
That single sentence does more for your risk position than any warranty clause, because it converts a marketing number into a measurable obligation. A supplier who will not sign it is telling you their number would not survive the test.
We publish absorption, float and equalisation voltages per model, and cycle data with the depth and temperature it was measured at, because a buyer who knows those three things can check our claims against anybody else's. That is a low bar and it is surprising how many suppliers clear neither.
The thing I actually want you to take away
Cycle counts feel like the hardest, most objective number on the datasheet. They are the softest one. Capacity you can measure in an afternoon with a load bank. Cycle life is a projection built on five assumptions, and four of them are usually unstated.
That does not mean the numbers are useless. It means they are only comparable when the assumptions match, and in a tender they almost never do.
So the next time three suppliers send you 1200, 1500 and 3000 for the same cell — do not average them, and do not pick the biggest. Ask each one what they measured, and watch which of them answers in a paragraph and which answers in a sentence.
The one who answers in a sentence already knows you are going to ask.
Looking for a reliable battery supplier?
Send us your requirements — model, quantity and target market. Quote within 24 hours.
Get a Quote